Failure Mode and Effect Analysis (FMEA) of Pneumatic System of CNC Milling Machine

  • Yudi Dwianda Maintenance and Repair Engineering Department, Politeknik Kampar, Indonesia
DOI: http://dx.doi.org/10.36842/jomase.v65i1.239

Abstract

The purpose of this study is to determine the type of failures, the causes, as well as efforts and proposed actions that can be taken to improve the performance of the pneumatic system of CNC milling machines. The Failure Mode and Effect Analysis (FMEA) method is used to find priority problems through Risk Priority Number (RPN) for pneumatic system of components of CNC milling machine. The results of critical component analysis were a leakage occurs in pneumatic valve component, which the most critical risk of the RPN value. It potential failure was caused the high humidity and poor air quality from the compressor, which the RPN of 392 and 384 respectively. The proposed improvement was the replacement of damaged components and optimizing the preventive maintenance, which follow the right operation and maintenance procedures recommended as suggested by the manufacturer.

##Keywords:## CNC Milling Machine, FMEA, Pneumatic system, RPN.
Published
Mar 30, 2021
How to Cite
DWIANDA, Yudi. Failure Mode and Effect Analysis (FMEA) of Pneumatic System of CNC Milling Machine. Journal of Ocean, Mechanical and Aerospace -science and engineering-, [S.l.], v. 65, n. 1, p. 14-18, mar. 2021. ISSN 2527-6085. Available at: <https://isomase.org/Journals/index.php/jomase/article/view/239>. Date accessed: 19 aug. 2024. doi: http://dx.doi.org/10.36842/jomase.v65i1.239.
Citation Formats
Issue
Vol 65 No 1 (2021): Journal of Ocean, Mechanical and Aerospace -science and engineering- (JOMAse)
Section
Articles

References

[1] Peng C., Lan, L., Liu Q. and Yao, J. (2013). Research on soft fault of computer numerical control system, Chemical Engineering Transactions, Vol.33: 973-978.
[2] Salvi, R.K. and Jindal, S. (2017). FMEA to enhance quality and efficiency of CNC machines: a case study in valve manufacturing industry, Industrial Engineering Journal, Vol.10, No.4, pp: 35-41.
[3] Degu, Y.M. and Moorthy, R.S. (2014). Implementation of machinery failure mode and effect analysis in Amhara Pipe Factory P.L.C., Bahir Dar, Ethiopia, American Journal of Engineering Research, Vol.03, No.1, pp: 57-63.
[4] Ambekar, S.B., Edlabadkar, A. and Shrouty, V. (2013). A review: implementation of failure mode and effect analysis, International Journal of Engineering and Innovative Technology, Vol.2, No.8, pp: 37-41.
[5] Liu, H.C., Liu, L. and Liu, N. (2013). Risk evaluation approaches in failure mode and effects analysis: A literature review, Expert Systems with Applications, Vol.40, pp: 828-838.
[6] Stamatis, D.H. (1995). Failure Mode and Effect Analysis : from Theory to Execution. ASQC Quality. Milwauke. USA.
[7] Filip, F.C. (2011). Theoretical research on the failure mode and effect analysis (fmea) method and structure, Advances in Manufacturing Engineering, Vol.2, pp: 176-181.
[8] Gupta, G., Mishra, R., (2017). A failure mode effect and criticality analysis of conventional milling machine using fuzzy logic: case study of RCM, Quality and Reliability Engineering International, Vol. 33, pp: 347-356.
[9] Kulkarni, P.V. and Shrivastava, R.K. (2013). Failure mode and effect analysis: process capability enhancement-a case study, International Journal of Engineering Research and Technology, Vol.2, No.4, pp: 1859-1868.
[10] Wang, X., Zhang, Y., Shen, G. (2016). An improved FMECA for feed system of CNC machining center based on ICR and DEMATEL method, The International Journal of Advanced Manufacturing Technology, Vol. 83, pp: 43-54.
[11] Ebrahemzadih, M., Halvani, G.H., Shahmoradi, B. and Giahi, O. (2014). Assessment and risk management of potential hazard by failure mode and effect analysis (fmea) method in yazd steel complex, Journal of Safety Science and Technology, Vol.4, pp: 27-135.
[12] Anes, V., Henriques, E., Freitas, M. and Reis, L. (2018). A new risk prioritization model for failure mode and effects analysis, Quality and Reliability Engineering International, Vol.34, pp:516-528.
[13] Ghivaris, G.A, Leksananto, K. dan Desrianty, A. (2015). Usulan perbaikan kualitas proses produksi rudder tiller di pt. pindad bandung menggunakan fmea dan fta, Jurnal online Institute Teknologi Nasional, Vol.4, No.3, pp: 73-84.