Send an email / attach file :
For more information, send an email or submit a paper to us.
Lists of Accepted Paper :
Mechanical Department |
[01] Experimental Study of Screw Turbine as Lower Head Power Generation ... This paper reports on a performance analysis based on the experimental data collected from different performance tests carried out on three inclination angle position of screw turbine prototype. |
Ocean and Aerospace Engineering Research Institute (OCARI) |
[02] Reliability of X80 to Buckle Curvature in Designing of Subsea Pipeline ... Buckling phenomenon is still to be crucial problem in severe operation of subsea pipeline. The Material grade X80 is selected with assorted pipeline thickness and diameter to observe the behaviour of material properties when impact on buckling load. |
Mechanical Engineering, UniversitiTeknologi Malaysia (UTM) |
[03] Computational Analysis of a Generic Bell 206B Helicopter Tail Rotor Blade using ANSYS FLUENT ...
This paper presents the computational analysis of three dimensional (3D) flow over the generic model of Bell 206B helicopter tail rotor blades using ANSYS Fluent Computational Fluid Dynamics (CFD) package.
|
||
Mechanical Department, Universitas Riau (UR) |
[04] Compressive Strength and Wear Behavior of Palm Slag Composites Using Various Composition Materials Content (wt%) ...
The compressive strength and wear behavior at room temperature of palm slag composites was experimentally investigated using various composition materials content (wt%).
|
||
Mechanical Department, Universitas Riau (UR) |
[05] Manufacturing Design for Plate Product of Palm Slag Composites ...Manufacturing design for plate product of palm slag composites have been investigated. The plate product of palm slag composites were compacted on a compression molding machinery using jigs and fixtures. Jigs and fixtures were modeled with finite element simulation to determine the stress distributions of a jigs and fixtures.
|
||
Mechanical Department, Universitas Riau (UR) |
[06] Influence of the Bending to the Strength of Concrete Reinforcement Steel Bar in the Peat Water ...Environmental conditions also affected to the physical and mechanical conditions of the reinforcement steel bar.Many varieties of corrosion environmental condition that was given, then the peat water scope was selected as a characteristic geographical condition in Riau Province.
|
||
Mechanical Department, (UR) - (ITB) |
[07] Failure Assessment Diagram Used for Integrity Analysis of
Cylindrical Shells with Crack
...The evaluation of Stress Intensity Factor is determined through J-integral parameter found using a finite element analysis with a specially-meshed strategy incorporating the crack. The result of the model is first verified with that of the Code for a number of cases, before being used for parametric study.
|
||
Mechanical Department, (UR) - (UTM) |
[08] Computational Study of Flow Structure after a Bluff Body with
The Effect of Underneath Wavy Surface using RNG model ...Present study, two-dimensional numerical solution for the same test condition has been performed by adopt the RNG, model to simulate the flow pattern after a rectangular bluff body of which has height to width ratio of two in various wavy surface conditions and Reynolds numbers.
|
||
Mechanical Department, Universitas Riau (UR) |
[09] Design and Manufacturing Hopper Distributor of Fertilizer using Metering Valve Machanism on Caltivator for Fertilization on Palm Oil ...This research aims to design and build the precision hopper (tank of fertilizer diverter), according to the required dose, and has the ability to deliver fertilizer volumes approximately equal on each tree.
|
||
Mechanical Department, Universitas Riau (UR) |
[10] Analysis of Design for Assembly (DFA) Prototype Machine on Separate Waste Ferromagnetic Materials and Non Ferromagnetic Materials ...DFA analysis will be obtaining the value of efficiency on assembly. Through this way, the efficiency value of machine prototype to separating waste, both, ferromagnetic and non-ferromagnetic materials can be achieved.
|
||
Mechanical Department, Universitas Riau (UR) |
[11] Design and Manufacture of Undercarriage Components on Model Excavator in Hydraulic and Pneumatic Laboratory, Universitas Riau ...This research was conducted with the aim to make modeling as excavators in general by using materials available in the market . Next calculate the speed , direction of turn with a different variation of the track ( ceramic , asphalt , soil ) and the maximum tilt angle that can be achieved by the excavator.
|
||
Mechanical Department, Universitas Riau (UR) |
[12] Modification and Testing Control System and Swing System on Model Excavator ...Laboratory of Hydraulics and Pneumatics Mechanical Engineering, Faculty of Engineering, University of Riau has produced a model excavator using pneumatic system, support on a controller box, equipped with buttons setting and motion rotary swing 120o. The research has modifications control system, remove control box under the excavator and change to the remote system.
|
||
Mechanical Department, (UR) - (UNAND) |
[13] Dimensional and Geometric Errors Sensitivity of three degrees of freedom Spherical Parallel Mechanism with Respect to Compenstable and Uncompensatable errors ...This research was worked on the three degrees of freedom spherical parallel mechanism named 3-URU parallel mechanism. The mechanism composed of platform as an output link, base as a fixed link and three identical kinematic chains. The kinematic chains consisting of universal, revolute and universal joints are mounted symmetrically to the base and the platform.
|
||
Announcement
Sponsors
Resty Menara Group, Pekanbaru, Indonesia
Titipan Kilat, Pekanbaru, Indonesia
CV. Andalas Kertasindo, Pekanbaru, Indonesia
